SiteScapes Inc. - Home Page Warranty & Finishes
 
 

Warranties

Powder coat: Powder coat products are warranted against defects in material or workmanship for a period of one year.

DuraCoat: DuraCoat products are warranted against defects in material or workmanship for a period of five years.

Stainless Steel / Galvanized: Stainless steel and galvanized products are warranted against defects in material or workmanship for a period of five years.

Limited twenty year warranty against structural failure of steel bench frames or steel bench assemblies, table frames, trash receptacle frames and planter frames.

Limited twenty year warranty against structural failure of all cast iron bench supports.

Limited twenty year warranty from the date of shipment of any Recycled Plastic Lumber Product, if said Lumber Product manifests material signs of splitting, cracking, rot, termite attack and/or corrosion.

SiteScapes, Inc. liability and the buyer's remedy under these warranties are limited to the repair, replacement or refund of the purchase price, at SiteScapes option, of products determined in SiteScapes reasonable judgment to be defective in workmanship or materials.

SiteScapes will not be held responsible for the costs incurred in labor to remove, install, or replace the alleged defective product.

SiteScapes warranties do not cover any defects or failures resulting from vandalism, negligence, accidents, abuse, lack of maintenance, improper use or installation, or unapproved modifications and repairs.

In addition, SiteScapes will not be held liable for ANY damage or injury as a result of product not that is not permanently anchored in place or not anchored properly.

Finishes

Color chart
onyx
cobalt
forest
brandy
ivory
sterling
slate
bronze
pearl

Color depiction may vary due to browser settings. Colors shown are only a representation of standard colors offered and should not be used as a substitute for manufacturer provided paint chips.

DuraCoat Finish ( Five year warranty )
1. Blast carbon steel, using 90 grit aluminum oxide, to a near white ultra-fine finish. This allows for removal of minute rust and mill scale, while prepping the steel for maximum powder adhersion.
2. Product is rinsed in an alkali chemical wash to further remove any surface rust or grease and oil.
3. Fresh water rinse
4. Product receives a phosphate treatment further promoting powder adhesion and inhibiting rust prior to coating.
5. Fresh water rinse
6. Product receives a non-chromate rust inhibitor/sealant.
7. Product is preheated 15-20 minutes to eliminate moisture and break down Faraday cages.
8. Product is air sprayed to further eliminate any remaining water collected in cracks and crevices.
9. Product is briefly cooled to optimum coating temperatures
10. An epoxy powder base is applied at 2.4 mils. This creates a durable corrosion resistant undercoat.
11. Product is baked 30-40 minutes to insure a proper cure.
12. A TGIC polyester powder top coat is applied at 8-10 mils. The polyester top coat is an exterior rated coating and maximizes protection against the elements.
13. Product is baked again 30-40 minutes to cure the final coat.


Powder coat finish ( One year warranty )
1. Blast carbon steel, using 90 grit aluminum oxide, to a near white ultra-fine finish. This allows for removal of minute rust and mill scale, while prepping the steel for maximum powder adhersion.
2. Product in raw form is fabricated from all pickled and oiled carbon steel to minimize unwanted mill scale.
3. Product is rinsed in an alkali chemical wash to further remove any surface rust or grease and oil.
4. Fresh water rinse
5. Product receives a phosphate treatment further promoting powder adhesion and inhibiting rust prior to coating.
6. Fresh water rinse
7. Product receives a non-chromate rust inhibitor/sealant.
8. Product is preheated 15-20 minutes to eliminate moisture and break down Faraday cages.
9. Product is air sprayed to further eliminate any remaining water collected in cracks and crevices.
10. Product is briefly cooled to optimum coating temperatures
11. A TGIC polyester powder is applied at 2.5-4 mils. The polyester powder is an exterior rated coating and maximizes protection against the elements.
12. Product is baked again 30-40 minutes to cure the final coat.


Colors available: Onyx (Black) Pearl (White) Forest (Green) Cobalt (Dark Blue) Ivory (Ivory) sterling (sterling) Slate (Dark Gray) bronze (Brown) Brandywine (Burgundy)

Stainless Steel and Galvanized also available ( Ten year warranty )

Bookmark and Share


 
SiteScapes is on facebook
 
 
archive
  Recycled Plastic Custom Plaques
  Hingetop Cast Iron Ends
more...
 
SiteScapes Site Furnishings
 
     
 
SiteScapes
 
  BBB ASLA NRPA ICSC USGBC MasterCard/Visa Accepted Facebook Fan Page